Plans

I have enjoyed the build part of the project and will make one or two more, perhaps another set of wooden rails and one with proper metal ones. I have been looking at camera cases on ebay, but there is a danger of buying an unsatisfactory,  flimsy product and I might wait for a camera fair (September 16th).

In the meantime, Ross Lamond is selling TipTop Happy Endings, which would be a useful addition.

Dream Machine manuals

Links to instruction manuals (where found) for each of the modules used in the various temporary instrument setups.

Allen Strange Dream Machine patch

Dream Machine patch
TipTop uZeus
Doepfer A149 SoU
TipTop X8000 Sequencer
Doepfer A140 ADSR
Doepfer A132-3 Dual VCA
Doepfer A180 Multiple
Malekko Wiard Anti-Oscillator
Doepfer A147 VCLFO
Doepfer A148 Dual S&H
Doepfer A175 Dual Inverter
Doepfer A180 Multiple
Doepfer A109 Signal Processor
Doepfer A110 VCO
Pittsburgh Outs

Noise

first noise

The Wart from Farnell arrived next day (Weds). The uZeus from Postmodular was sent on Thurs, using the Post Office's 'guaranteed by 1 the next day' service, and arrived at 7am on Saturday (the PO's web site explains that, during the Olympics, next day becomes the day after).

uZeus

I found that the celebrated case builder Ross Lamond stocks TipTop power leads and also ships quickly - that arrived on Friday. So on Saturday morning all the essential kit was here (Rhythm Active shipped the Pittsburgh Outs on Saturday).

foam replacement

The uZeus is an impressive piece of kit - the engraved statement watch out hot surface is true: the faceplate is a radiator. I set up the framework outside the case and it burbled happily on TipTop power through a Logitech X-140 while I replaced the foam with a wooden framework.

complete

I set up the Doepfer Dream Machine subset and then the full Strange Dream Machine and I am still fiddling with the latter. There is space for a second VCO until the Outs arrives, so I will add that today.


Snaps to follow and then noises.

Education

Two good beginners' guides.

Nearly there

The frame

Back in the case

The wood is done, first pass at least. Here's the frame, my starting point today. Add top bottom and middle and it's done.

Power

I tried Schneiders for the uZeus but couldn't get their ordering system to work. That could be a good thing as, while awaiting a reply to a query, David at Postmodular replied with confirmation of stock so I will pursue that. Neither seem to have a Pittsburgh Outs at the moment.

On the Case, let's pause for a moment to acknowledge that the case insert, having removed the padding is reminiscent of the great Mondrian  and move on.

Taking out the interstices confirmed that my dad, bless the old bugger, built things to last and that's where I got that inclination. Now ready to build the framework, allowing for the possibility of a storage space if that works with a Dream Machine in place. I visited the splendid and nearby Modern Screws for some suitable product - they only had countersunk, rather than the panhead I need, but they will do for now (£1.56 for a box). I also called into B&Q (just round the corner) for some wood, but can probably take it back and use offcuts already in stock - but better safe than sorry as I hope to begin the wood build (except for the possible storage compartment) tomorrow.

Dream Machine

One of the prerequisites for the project is that The Case should be large enough to contain a Dream Machine. This was defined in the best book available on (modular) synthesis, Allen Strange's Electronic Music Systems, Techniques and Controls. Diagram right.
The components are:

• Two random voltage sources - Doepfer's SoU provides two, 12+4HP
• Sequencer - my smaller is the Analogue Solutions, about 18HP
• VCLFO A-147 8HP
• S/H A-148 4HP
• VCO the Anti-Oscillator is 14HP
• Inverter A-A175 4HP
• Two VCAs - there's one on the A109 Signal processor, I need another: a Doepfer A-132 dual VCA is 4HP
• ADSR A-142 8HP

And the likely permanent modules:

• Signal Processor A-109 20HP
• uZeus 4HP
• Outs 6HP

Total Dream = 76ish

Standards = 30
total = 106

So that's far too much for the 67HP case. Think again. [next day] Silly me, I have two lots of 67HP so carry on.


67*2 = 134 - 106 = 28 free for some sound processing or a second VCO to provide some other notes. The Metasonix R-54 is around 22HP, still leaving 6HP, but not with storage. What is the narrowest VCO?

On power, the uZeus comes with two power leads for 5+5=10 modules and allows another lead for 15 in total.

The case

 I have the case.

I have some Schroff rack inserts left over from the Cupboard but no rails left. Somewhere I have a box of the rails that you get with Doepfer DIY kits (the sort you insert the nuts into), but I'm not sure where.

For the first effort, I might try just a wooden structure and screw the units directly into the wood.

The case is large enough for two rows, certainly if I go 'all wood', not certain with aluminium, until I find the rails. It is 36cm wide and 7cm deep, so it will only take modestly deep modules.

I have emailed David at Postmodular about getting an eZeus power supply - they are not the currently in stock list, though the f(h) power unit is, so that can be a fallback. No answer yet, though he usually takes a few days. SchneidersBuero seem too have them.

I am supposed to be decorating next week, but if I could get the eZeus, this could be running in a week. It always takes a lot longer than I expect.

I had to look it up - an HP is 0.2" - the case is just over 13.5", so that's two rows of around 67HP. The next job is to work out what I need for a Dream Machine and see whether it will fit. It would be nice to  allow some storage space for the wall wart, cables etc., but that might not be possible. It did occur to me today that if the case is too small then I can spend some quality time touring camera fairs to corner the market in larger cases and, no doubt, buy more cameras too. There are no downsides to this plan.

Temporary Instrument 1 (archive, June 2009)

I mentioned at the Brighton meet that I hadn't bettered one of my earliest patches, a standard Doepfer setup using the A-149 'Source of Uncertainty'. It is called Sonata 9 Jun 2009 and here it is.

Gear Lust I

Despite the outrageous price tag of £390, an early acquisition must be the Makenoise Phonogene.

Modules I

So. What shall we have in the case?
I imagine there will be some permanent fixtures.

• The obvious starting point is the Tiptop uZeus.
• Not many people seem to use the Doepfer A-109 Signal Processor, but I think it's great. There are three in the Cupboard: I'll sacrifice one. 
• The A-109 provides most of the basics except an envelope, so I need a narrow ADSR. I might have a spare A-140, else perhaps Circuit Abbey's ADSRjr.
• At least one oscillator. I have some spares, but the Malekko Anti-Oscillator is my favourite.
• The cupboard uses a Cwejman MX-4S and an Analogue Systems RS270. For the TI case, I'll get a Pittsburgh Outs.
• No patch is complete without at least one VCLFO interfering, either Doepfer's A-147 (two in stock) or Pittsburgh's VILFO (none yet).

How much space will that leave?

I'll return to this subject.

Intro

That might sound like something bankers do to each other, but this is actually about modular synthesis.
I started a blogger entry a few years ago then switched it to my own web site at SnapDragon, which will probably continue. The blog detailed my gradual acquisition of euro-format modules and the building of the Cupboard.

Today I attended a Muffwiggler meeting in Brighton but could not contribute my own wurble-bleeps, so, as recently concluded, I need a portable setup. There are some snaps of the meeting here.

Tony of Synovatron was there - he has published details of converting a Halfords tool case (that link might not last), details here. This is powered by a Doepfer DIY Kit 1. My first inclination was to follow the same route, but I might seek simplifications and enhancements. The Synovatron blog notes that 'the case is just hardboard with a thin aluminium veneer': I have had an aluminium camera case for 40 years (bought when in school in the late 60s or early 70s - my dad customised the interior), no longer in use, which is far more solid. Regarding the power supply, I liked the look of the Tiptop microZeus and will go with that.

The plan is to build a case which will allow me to work in detail on subsets of the Cupboard and, of course, turn up to outside events and play.

The minimum requirement is that is should be large enough to run a Dream Machine (and there must, of course, be the components of a Dream Machine left in the Cupboard). The diagram is from Allen Strange's seminal Electronic Music Systems, Techniques and Controls.

The case will allow the development of a series of Temporary Instruments. I will document the case and the instruments here.